Skip to content
+32 (0) 9 340 44 04 info@eco2box.com

TL;DR Glass or polypropylene for plant tissue culture: glass as a material weighs about 2.4 times as much, can break, needs washing and autoclaving before every reuse, and leaves gas exchange to the cap or plug you fit. Eco2Box polypropylene is lighter, leaves no broken glass in the lab, and its lid closes hermetically with a gas exchange you set by filter grade. We recommend at most 5 uses. Test both on your own crop.

Labs that ask whether glass or polypropylene is the right material for plant tissue culture usually compare a jar they already wash and reuse with a plastic container they would have to buy. This page puts the two materials side by side, with a source for every figure and a clear note where no figure exists.

What is the difference between glass and polypropylene tissue culture vessels?

Glass vessels are jars, tubes and flasks, normally of borosilicate glass, that a lab washes, autoclaves and reuses, and closes with a cap, plug or film. Polypropylene vessels are moulded plastic containers. The Eco2Box is a transparent polypropylene vessel with a polypropylene cover that closes hermetically and holds a depth filter, so gas exchange runs through the filter.

A university propagation course sums up the shared requirement in two sentences: culture containers “can be made of glass or plastic, but must either be bought sterile or be able to be autoclaved”, and their lids “must allow gas exchange but prevent entry of pathogen spores” (UF/IFAS tissue culture terminology).

How do glass and polypropylene compare, property by property?

Glass is heavier, can break, is washed and autoclaved before each reuse, and its gas exchange depends on the closure. It takes more heat, and the sources read state no limit on its autoclave cycles. Eco2Box polypropylene is the lighter material and has a closure with a chosen gas exchange rate. For clarity and washing labour no comparable figures are published. The table gives each property with its basis.

Property Borosilicate glass vessel Eco2Box polypropylene vessel with filter cover
Clarity Clear. No light transmission figure is cited here. Clear enough to check plantlets by eye without opening. Polypropylene as a material is harder to make fully transparent than some other plastics. Light transmission figure: not published.
Heat range Typical maximum of about 500 °C for borosilicate glass. Container and filter keep their properties between -5 °C and +135 °C.
Autoclave at 121 °C Yes, for Type I borosilicate glass. Other glass types are not rated for it. Yes for untreated polypropylene. Gamma irradiated articles are supplied sterile; autoclaving them is not recommended.
Autoclave cycles No limit is stated in the sources read. At most 5 uses recommended; never more than 10. The material becomes more brittle with each cycle.
Thermal shock and breakage Withstands a temperature difference of about 166 °C without fracturing. Glass can still break when dropped or knocked. No breakage rate is published. Plastic, so no broken glass in the lab. Brittleness rises with each autoclave cycle.
Weight of the material About 2.23 g/cm³. 0.895 to 0.93 g/cm³ for polypropylene, so glass weighs about 2.4 to 2.5 times as much for the same volume of wall material. Wall thickness differs, so this is not a weight per vessel.
Closure and gas exchange Depends on the closure you fit: cap, plug, foil or film. The cover closes hermetically and the filter grade sets the exchange: Kv 9.87 to 81.35 air replacements per day in round sets.
Sterile on arrival The lab washes and autoclaves. Untreated for your own autoclave, or gamma irradiated and supplied sterile.

Sources for the glass column: the autoclave compatibility list of the University of Utah and the encyclopedia entries on borosilicate glass and polypropylene. The Eco2Box column comes from ECO2’s product specifications.

How many autoclave cycles does each material take?

Untreated Eco2Box polypropylene vessels and covers are autoclaved at 121 °C before first use; we recommend at most 5 uses, the plastic never takes more than 10, and it becomes more brittle with each cycle. For borosilicate glass the sources read give no cycle limit: the University of Utah lists Type I borosilicate glass as autoclavable and stops there.

That is the main point in favour of glass: no cycle limit is stated for a jar, while an untreated polypropylene container is best replaced after 5 uses. The other side of that sum is the washing, drying and checking between cycles. No published figure was found for that time per vessel, for either material, so count it in your own lab before you compare.

Does the material or the closure decide the gas exchange?

The closure decides, not the material. On a glass jar the air is replaced through the cap, plug or film you fit, which is why a lid has to allow gas exchange. On an Eco2Box, with the cover closed, gas exchange runs through the filter in the cover, and the filter grade sets the rate.

Eco2Box has four filter grades, L, XL, XXL and XXL+. Measured as Kv, the number of times the air space is replaced per day, round sets go from 9.87 for L to 81.35 for XXL+. That makes the exchange rate a property you choose, not a result of how tightly a lid happens to fit. The guide on choosing a filter grade has the full table.

More exchange is not a goal in itself. Published studies show that gas exchange should be matched to the species, the stage and the medium, and for some species low-exchange conditions gave the stronger result. A glass jar with a closure that suits your crop can be the right environment.

What did a study measure when it compared glass with a filtered plastic vessel?

One open-access study compared glass tubes with a filtered Eco2Box vessel, on one species. In doubled haploid onion, under one of two protocols and with 23 to 26 embryos per container type, the Eco2Box vessel gave 4.2% hyperhydricity (glassy, watery plants) against 34.6% in glass tubes. Under the other protocol there was no significant difference.

The onion study is Fayos et al. 2015, Frontiers in Plant Science 6:384. It compared glass tubes with plastic plugs, a culture box from another manufacturer and an Eco2Box vessel with a green filter. Under protocol B, with 23 to 26 embryos per container type, hyperhydricity was 4.2% in the Eco2Box vessel, 34.6% in the glass tubes and 34.8% in the other box. Of the embryos, 70.8% became acclimatised plants from the Eco2Box vessel, 23.1% from the glass tubes and 52.2% from the other box.

The limits belong to the numbers. Under protocol A, with 16 to 35 embryos per container type, hyperhydricity did not differ significantly between the three containers, and the other box gave the most acclimatised plants (37.5%). Plant density differed: 4 to 6 plants per Eco2Box vessel against 2 to 3 per box of the other type. It is one species in one lab, and which filter grade the green filter was is not confirmed. In the same paper, glass tubes closed with plastic plugs or with cellulose plugs showed no significant difference.

The study does not isolate the material. It compares whole vessels: wall, volume, closure and plant density together.

When is glass the right choice?

Glass is the right choice when your process goes above 135 °C, when you want one vessel to last through many sterilisation cycles and have the washing in place, or when your protocol already gives good plants in glass. Borosilicate glass tolerates about 500 °C, and no cycle limit is stated for it.

  • Heat above 135 °C. Eco2Box containers and filters keep their properties between -5 °C and +135 °C. A step hotter than that is outside the range of the Eco2Box.
  • Many cycles per vessel. Untreated polypropylene is best used at most 5 times. No cycle limit is stated for borosilicate glass, so a lab that already runs a washing line and loses little glass can get more cycles from a jar.
  • A protocol that works. A different vessel can change the gas exchange. If plants from your glass jars root and transfer well, test a new vessel next to them before you change anything.

When does polypropylene with a filter lid fit?

Polypropylene with a filter lid fits when you want to choose the gas exchange, when breakage and weight cost you time, or when you want vessels that arrive sterile. The Eco2Box cover closes hermetically, the filter grade sets the exchange, and the vessel is clear enough to check plantlets without opening it.

  • Gas exchange as a setting. Four grades from Kv 9.87 to 81.35 per day in round sets, so you can step up or down per stage.
  • A closure that closes. The cover closes 100% hermetically onto the vessel, which shuts the gap between lid and vessel as a route for contamination. Handling and micro-organisms inside the plant material remain routes that no lid changes.

The O118/80 with filter (565 ml) is one of the Eco2Box bestsellers. The full product range lists every size.

How do you compare glass and polypropylene in your own lab?

Run both vessels side by side on one crop, one medium and one shelf, and count per usable plant, not per vessel. Five steps cover it.

  1. Pick one crop and one stage where you see losses or extra work.
  2. Fill your glass jars and the polypropylene containers from one batch of medium, with the same number of explants for the same volume of medium where the shapes allow it.
  3. Take two neighbouring filter grades, for example XXL and XXL+, so you see the effect of the exchange rate as well as the vessel.
  4. Record condensation, contamination, glassy plants, drying of the medium and breakage per vessel type.
  5. Follow the plants through transfer and count how many are saleable or usable. Add your own time for washing, filling and closing.

Frequently asked questions

Can polypropylene tissue culture containers be autoclaved?

Yes. Polypropylene resists autoclave temperatures, and untreated Eco2Box vessels and covers are autoclavable at 121 °C. The exception is a gamma irradiated article: it is supplied sterile, and autoclaving it is not recommended. Polystyrene is different: the Eco2Box RA trays and RDA covers are polystyrene, heat resistant to 85 °C and not for the autoclave.

How many times can I reuse a polypropylene container?

Untreated Eco2Box polypropylene vessels and covers can be used up to 5 times, with an autoclave cycle before each use; that is our recommendation, and the plastic never takes more than 10. The material becomes more brittle with each cycle, so check for cracks and a cover that still closes before you refill.

Is polypropylene clear enough to check my cultures?

Eco2Box vessels are clear, so plantlets can be checked by eye without opening the container. Polypropylene is in general harder to make fully transparent than polystyrene, and ECO2 has not published a light transmission figure, so compare a sample under your own lamps.

Do glass jars give less gas exchange than containers with a filter?

That depends on the closure of the jar, not on the glass. No published table was found that puts exchange rates of caps, plugs, film and filters side by side. For an Eco2Box the rate is known per filter grade: 9.87 to 81.35 air replacements per day in round sets.

Does switching from glass to polypropylene reduce hyperhydricity?

Not by itself. A review names the aeration of the vessel among the main factors, next to the mineral and hormonal composition of the medium. In one onion study an Eco2Box vessel with a filter gave 4.2% hyperhydricity against 34.6% in glass tubes under one protocol, with 23 to 26 embryos per container type, and no significant difference under the other protocol. Plant density also differed between the vessels in that study.

Request a sample set or ask a question

A sample set of filtered Eco2Box containers is available on request, so you can run polypropylene next to the glass you use now. Request a sample set, or ask a question and tell us the species, the stage and your current vessel. We then propose which filter grades to compare.

Related guides: Polypropylene containers for tissue culture: the facts, Single use or reuse: the real cost of a culture vessel.

Sources checked on 20 November 2026: University of Utah autoclave compatibility list; UF/IFAS tissue culture terminology (2023); encyclopedia entries on borosilicate glass and polypropylene for density and temperature figures; Fayos et al. 2015, doi 10.3389/fpls.2015.00384; Polivanova and Bedarev 2022, doi 10.3390/plants11233313. Eco2Box figures come from ECO2’s product specifications and filter guide.