Skip to content
+32 (0) 9 340 44 04 info@eco2box.com

TL;DR Plants per vessel is a division: the base area of the container divided by the floor area your protocol allows per shoot, rounded down. An Eco2Box OV80 has a 64 cm2 base, so it takes at most 21 shoots at 3 cm2 each and 16 shoots at 4 cm2 each. The tables on this page do the sum for eight Eco2Box articles. They give an upper limit from published sizes, not a crop recommendation.

How many plants per vessel a lab uses is rarely written down as a rule. It is a habit that came with the vessel. When the vessel changes, the count has to be worked out again, and volume in millilitres does not help. This page gives the method and two worked tables. It contains no crop trial and no recommended density.

How many plants fit in one vessel?

Divide the base area of the vessel by the floor area one shoot needs, and round down. In formula form: plants per vessel = base area in cm2 / floor area per shoot in cm2. For an Eco2Box O118/80 with a 79 cm2 base and 4 cm2 per shoot, the result is 19 shoots.

The sum also runs the other way. If the number of shoots is fixed, divide the base area by that number to see how much floor each shoot gets: 20 shoots in the same O118/80 get just under 4 cm2 each (79 divided by 20 is 3.95, shown as 4.0 in the table). Both directions are in the tables below.

Which two numbers do you need?

You need the base area of the vessel and the floor area per shoot. The base area of each Eco2Box set is calculated from its published base size. The floor area per shoot comes from your own protocol, and you can derive it from the distance between shoots.

  • From spacing: on a square grid, floor area per shoot is the spacing multiplied by itself. Shoots 1.5 cm apart use about 2.3 cm2 each, 2 cm apart 4 cm2 and 2.5 cm apart about 6.3 cm2.
  • From your current vessel: measure the inside floor, calculate its area and divide by the number of shoots you place in it now.
  • From the shoot itself: measure the widest cluster on the last day of the cycle, not the explant on day one.

How many shoots fit in each Eco2Box article?

The largest base area in the table, the Eco2Box O118/80 with 79 cm2, takes at most 39 shoots at 2 cm2 per shoot and 13 shoots at 6 cm2 per shoot. The table gives the count for five floor areas per shoot, rounded down, for every article with a published base size.

Article (base area) 2 cm2 per shoot 3 cm2 4 cm2 5 cm2 6 cm2
O95/114 (44 cm2) 22 14 11 8 7
O95/40 and O95/60 (50 cm2) 25 16 12 10 8
OV80, O118/120 and O118/140 (64 cm2) 32 21 16 12 10
O118/50 (71 cm2) 35 23 17 14 11
O118/80 (79 cm2) 39 26 19 15 13

Base areas are the rounded figures from the guide on container size for blueberry and strawberry: a circle for the round bases and an ellipse for the oval OV80. Volumes and heights per article are in the product range.

How much floor does each shoot get at a fixed count?

At 20 shoots per vessel, a shoot gets 4.0 cm2 in the Eco2Box O118/80, 3.2 cm2 in the OV80 and 2.2 cm2 in the O95/114. The table gives floor area per shoot, in cm2, for five counts.

Article (base area) 5 shoots 10 shoots 15 shoots 20 shoots 25 shoots
O95/114 (44 cm2) 8.8 4.4 2.9 2.2 1.8
O95/40 and O95/60 (50 cm2) 10.0 5.0 3.3 2.5 2.0
OV80, O118/120 and O118/140 (64 cm2) 12.8 6.4 4.3 3.2 2.6
O118/50 (71 cm2) 14.2 7.1 4.7 3.6 2.8
O118/80 (79 cm2) 15.8 7.9 5.3 4.0 3.2

Two readings help. Going from 20 to 25 shoots in the same vessel takes 20% of the floor away from every shoot. And at the same count, the O118/80 gives each shoot 23% more floor than the OV80, although the two hold nearly the same volume. Those two sets are compared in O118/80 or OV80.

Why is the table an upper limit?

The table divides areas, and real shoots do not tile a floor. Expect the count that works in practice to be lower than the table, for three reasons that the published sizes cannot capture:

  • The edge. A grid on a round or oval floor loses places along the rim.
  • Growth. A shoot that becomes a cluster during multiplication needs the floor of the cluster, not of the explant.
  • Handling. Forceps need room between shoots.

The round vessels are wider at the cover than at the base, so there is more width higher up than the base area suggests. The count on the floor stays the same. Lay the shoots out once in a sample set before fixing a number.

What changes when you put more plants in one vessel?

More plants per vessel means less floor, less air and less medium per plant, while the filter stays the same. The Eco2Box filter guide lists the number and size of plants per container among the conditions that change the real gas exchange in a vessel.

Two published studies touch on space per plant, each on a single crop. Malik et al. 2022 grew the same starting amount of orchid tissue for 11 weeks in plastic vessels of 120 to 470 ml, and the growth index rose from 1.367 to 7.36 with vessel size. That study used other vessels than Eco2Box. In Fayos et al. 2015, on doubled haploid onion with 16 to 35 embryos per arm, the Eco2Box vessel held 4 to 6 plants and one of the two other containers held 2 to 3. Density differed between the arms, so that study cannot separate the vessel from the plant count. Record both when you compare.

Which mistakes are common when counting plants per vessel?

The first mistake to avoid is keeping the old count in a new vessel without checking the floor. Four more:

  • Counting against volume. Two vessels of about 500 ml can differ by 31% in floor area, as the O95/114 and the OV80 do.
  • Measuring the explant. Measure the shoot or cluster on the last day of the cycle.
  • Changing vessel and count together in a trial. Keep one of the two equal.
  • Reading the table as advice. It is arithmetic. Your crop and your stage set the density.

Frequently asked questions

How many plants fit in an OV80?

The Eco2Box OV80 has a calculated base area of 64 cm2. That gives at most 32 shoots at 2 cm2 per shoot, 21 at 3 cm2, 16 at 4 cm2 and 12 at 5 cm2. These are upper limits from the published base size of 125 x 65 mm.

How many plants fit in an O118/80?

The Eco2Box O118/80 has a 100 mm round base, which is 79 cm2. That gives at most 39 shoots at 2 cm2 per shoot, 26 at 3 cm2, 19 at 4 cm2 and 15 at 5 cm2. Expect fewer in practice, because a grid loses places along a round rim.

How do I convert plant spacing into floor area per shoot?

Multiply the spacing by itself. Shoots 2 cm apart on a square grid use 4 cm2 each, and shoots 2.5 cm apart use about 6.3 cm2. Then divide the base area of the Eco2Box article by that figure and round down.

Does Eco2Box recommend a number of plants per vessel?

No. ECO2 publishes no density per crop, and the published studies differ per species. Eco2Box gives the base area per article so you can apply the density from your own protocol, and proposes two sizes to compare on your own plants.

Can I use the tables for the rectangular TP containers?

Not yet. The base sizes of the Eco2Box TP sets are not confirmed, so no floor area is listed for them. With a sample in hand the method is the same: measure the inside floor, multiply length by width and divide by the floor area per shoot.

Check the count on your own shoots

Tell us the crop, the stage and the number of shoots you place per vessel now, and we propose two Eco2Box articles that cover that floor. A sample set is available on request through the sample page, so you can lay the shoots out before you decide.

For a question about sizes, use the contact page. The method for the whole choice, with height and filter grade, starts from the same two numbers.

Related guides: How to choose a tissue culture container: size and floor, Raspberry micropropagation: vessels and filter grades.

Sources: Eco2Box product specifications (base sizes per article) and filter guide, checked on 20 November 2026; Malik et al. 2022, BioTechnologia 103(1); Fayos et al. 2015, Frontiers in Plant Science 6:384. Base areas, counts and floor per shoot are arithmetic from the published sizes, not measurements and not a crop recommendation.