Skip to content
+32 (0) 9 340 44 04 info@eco2box.com

TL;DR For orchid propagation in vitro, choose the vessel per stage. Sow and start on a low filter grade (L), multiply on a mid grade, and move to a taller vessel when the plantlets need height. For the last months before sale, an unfiltered polystyrene RA tray is an option, with clear limits: it does not close hermetically and it is heat resistant to 85 °C. No Eco2Box orchid trial exists, so compare on your own plants.

Orchid seed is fine as dust and growth in vitro is slow, so plantlets stay in one vessel for a long time. Orchid labs ask two things: which vessel at which stage, and whether the last stage needs a filter at all. This page answers per stage from the published Eco2Box specifications and two published studies.

Which vessel suits orchid propagation at each stage?

Use a low gas exchange for sowing and young protocorms, a standard grade for multiplication and replating, and a taller vessel for growing on. The table gives a starting point per stage from the Eco2Box filter guide and the published sizes. It is not a trial result.

Stage What matters most Eco2Box articles to compare Grade to start with
Sowing and protocorms (the first small green bodies) Slow growth, medium must not dry out O95/40, O95/60, O118/50 L
Multiplication and replating Floor area per plantlet OV80, O118/80 XL or XXL, side by side
Growing on and rooting Height and a long cycle O118/120, O118/140 Test two grades; watch the medium
Last months before sale A vessel that leaves with the plant Filtered set, or an RA tray without filter See the section on the last stage

Sowing and protocorms: which grade for fine seed?

Start on grade L. The Eco2Box filter guide suggests L for sensitive plants and slow growers, and names fine seeds, young seedlings and initiation as examples. In the round sets L gives a Kv of 9.87, which means the air space is replaced about ten times a day.

A low grade fits this stage for a practical reason: more ventilation means less condensation and a higher risk of the medium drying out, and a sown vessel stands for a long time. Low vessels are enough here. The O95/40 is 40 mm high on a 50 cm2 floor, the O95/60 is 60 mm high on the same floor, and the O118/50 is 50 mm high on 71 cm2.

Multiplication and replating: how much floor per plantlet?

Count plantlets against the floor of the vessel. The Eco2Box O118/80 has a 79 cm2 floor and the OV80 a 64 cm2 floor, both at 80 mm height, so the round set gives 23% more floor at nearly the same volume. Divide the floor by the number of plantlets you replate to see what each one gets.

One published orchid study used this size. Pramanik et al. 2024, a study on root and fruit movement in Erycina pusilla, used the Eco2Box O118/80 with an XL filter in its methods, with about 20 ml of medium per container. The paper used the vessel; it did not compare or assess it. The counting method is explained in the guide on container size for blueberry and strawberry, and the two sets are compared in O118/80 or OV80.

Growing on: when does an orchid need a taller or larger vessel?

Move up when leaves reach the cover before the cycle ends. The Eco2Box O118/120 and O118/140 are 120 and 140 mm high, which is 50% and 75% more than the O118/80, and they take the same 118 mm cover.

One study suggests that size itself matters for orchids. Malik et al. 2022 grew protocorm-like bodies of a Dendrobium hybrid for 11 weeks in plastic vessels of 120 to 470 ml. The growth index rose from 1.367 in the 120 ml vessel to 7.36 in the 470 ml vessel. A 280 ml glass vessel reached 7.123, so volume was not the only factor. That study used other vessels than Eco2Box and one hybrid, so read it as a reason to test a larger size, not as a rule.

The last stage: filter or no filter?

Both are possible, and they are different products. A filtered Eco2Box set closes hermetically and exchanges gas through the filter. An RA tray with an RDA cover is polystyrene, has no filter, does not close hermetically and is heat resistant to 85 °C.

Property Filtered set (polypropylene) RA tray with RDA cover (polystyrene)
Closure Closes hermetically Does not close hermetically
Gas exchange Through the filter, at the grade you choose No filter
Heat Untreated sets are autoclavable at 121 °C Heat resistant to 85 °C
Typical use in this stage Plants that stay in a closed vessel until they leave A vessel that leaves with the plant

The tray is an option when the vessel leaves with the plant and does not come back. The trade-off is the closure: without a hermetic cover, the closure stays a possible route in for the months the plants still stand in the lab. See the RA tray with RDA cover and the filtered OV80.

Where does contamination in orchid cultures come from?

The closure is one of three routes. Handling by the operator and micro-organisms from inside the plant tissue are the other two, and no lid changes those. An Eco2Box filter lid closes the route through the closure, and that is the whole claim.

Orchid cultures stand for a long time, so check all three routes before you change the vessel.

Which mistakes are common with orchid vessels?

The first mistake to avoid is taking the highest gas exchange for a slow crop. The full list:

  • Starting seed on a high grade. The medium has to last, so start low and step up one grade at a time.
  • Keeping plantlets in a low vessel until the leaves bend under the cover.
  • Putting a polystyrene tray in the autoclave. It is heat resistant to 85 °C.

Frequently asked questions

Which Eco2Box container do orchid labs start with?

For replating, compare the Eco2Box OV80 and the O118/80, both 80 mm high with 64 and 79 cm2 of floor. One published orchid study used the O118/80 with an XL filter in its methods. For sowing, a lower set such as the O95/60 is enough.

Which filter grade for orchid seed sowing?

Grade L. The Eco2Box filter guide suggests L for sensitive plants and slow growers, and names fine seeds, young seedlings and initiation. L gives a Kv of 9.87 per day in round sets and 7.44 in the oval set.

Do orchids in the final phase need a filter?

That is a choice per lab, and no published comparison was found. Eco2Box also has RA trays without a filter. The tray does not close hermetically, so the closure stays a possible route for contamination for as long as the plants stand in the lab.

Can I autoclave the RA tray?

Eco2Box RA trays and RDA covers are polystyrene and heat resistant to 85 °C. An autoclave cycle runs at 121 °C. Untreated polypropylene sets with a filter cover are autoclaved at 121 °C before first use, and we recommend at most 5 uses.

Is there an orchid study with Eco2Box vessels?

One orchid paper, Pramanik et al. 2024 in Applications in Plant Sciences, used the Eco2Box O118/80 with an XL filter in its methods. It studied plant movement and did not compare vessels. Eco2Box has no orchid trial of its own.

Compare two vessels per stage on your own orchids

Tell us the genus, the stage, the number of plantlets per vessel and how long they stay in it, and we propose which Eco2Box articles and grades to compare. A sample set is available on request through the sample page.

For a question, use the contact page. The reasoning per grade is in which filter grade to use at which stage.

Related guides: Plants per vessel: how many shoots fit in one container, Green or white filter: gas exchange (Kv) per Eco2Box grade.

Sources: Eco2Box product specifications and filter guide, checked on 20 November 2026; Pramanik et al. 2024, Applications in Plant Sciences 12(1):e11567; Malik et al. 2022, BioTechnologia 103(1). Floor and height comparisons are arithmetic from published sizes. No Eco2Box orchid trial exists.