Skip to content
+32 (0) 9 340 44 04 info@eco2box.com

TL;DR To prevent hyperhydricity, work on two sides: the medium (firmer gel, lower cytokinin, less ammonium) and the vessel (more gas exchange through the closure). The 2022 review used here concludes that no measure is universal. The vessel lever can be tested without changing the recipe: run the same crop and medium in two ventilation levels side by side. More ventilation also dries the medium faster, so match it, do not maximise it.

Hyperhydricity, also called vitrification, turns shoots glassy and watery. This guide separates what you can change in the medium from what you can change in the vessel, and says where the evidence stops.

What is hyperhydricity?

Hyperhydricity is a physiological disorder of plants grown in vitro in which the tissue holds too much water. A 2022 review by Polivanova and Bedarev calls it the most common physiological disorder in in vitro cultivation. Hyperhydric shoots have thickened stems, short internodes and translucent, fragile, twisted leaves.

The water sits in the wrong place. In hyperhydric Arabidopsis seedlings, the share of air in the apoplast, the space outside the leaf cells, fell from 85% to 15% (van den Dries et al. 2013). Gas exchange inside the leaf is then reduced, and the 2022 review notes that hyperhydricity prevents plants from adapting after transfer.

What causes hyperhydricity?

Hyperhydricity has several causes that act together, in three groups: the medium, the conditions in the vessel, and the plant material. Polivanova and Bedarev list them as:

  • the composition of the medium, the growth regulators and the type of gelling agent;
  • the cultivation conditions, among them the aeration of the vessel;
  • the explant: its type, size, age and genotype.

The same review names high relative humidity and the build-up of gases in a confined vessel as factors. No review we read gives a humidity figure a lab could steer on, and a 2025 review by Barua and colleagues lists similar factors and gives no threshold either.

How do you prevent hyperhydricity through the medium?

On the medium side, three changes come back in the reviews: a firmer gel, less cytokinin and less ammonium. Each has a cost, and the right dose differs per species.

Lever in the medium Direction that reduces hyperhydricity What it can cost
Gel strength More agar. The review calls this effective in many species Multiplication can drop, because the plant takes up medium components less easily
Gelling agent The effect depends on type and brand; liquid or soft medium raises the risk A change of agent changes more than firmness
Cytokinin Lower concentration, or another cytokinin Fewer shoots per cycle
Nitrogen Less ammonium relative to nitrate A new medium recipe to validate

The directions, and the cost of more agar, come from Polivanova and Bedarev 2022. The other costs are our own reading. These are directions, not doses: the review gives no figure that holds across species.

How do you prevent hyperhydricity through the vessel?

On the vessel side there is one lever: how much gas the closure lets through. Ventilation lowers the build-up of gases in the vessel, and the reviews list it among the measures that work in several species. In an Eco2Box vessel that lever is the filter grade, a property you choose.

Eco2Box filter grade Kv, round vessels (air replacements per day) Kv, oval vessel (per day)
L (white) 9.87 7.44
XL (yellow) 13.09 9.84
XXL (red) 15.58 10.83
XXL+ (green) 81.35 62.87

Kv is the number of times per day the air in the vessel is replaced through the filter. No Kv is published for the rectangular TP vessels. More ventilation means less condensation and a higher risk that the medium dries out, so the aim is to match gas exchange to species, stage and medium. The guide on choosing a filter grade gives a starting grade per stage.

What did the one independent container study measure?

One independent study compared an Eco2Box vessel with two other containers, and it found less hyperhydricity under one of its two protocols. Fayos et al. 2015 regenerated doubled haploid onion plants in a glass tube, an Eco2Box vessel with a green filter, and a culture box from another manufacturer.

Protocol and container Embryos Hyperhydric Acclimatised
A, glass tube 35 17.1% 20.0%
A, Eco2Box vessel 28 10.7% 25.0%
A, other culture box 16 18.8% 37.5%
B, glass tube 26 34.6% 23.1%
B, Eco2Box vessel 24 4.2% 70.8%
B, other culture box 23 34.8% 52.2%

Read the limits with the numbers. Under protocol A the hyperhydricity figures did not differ significantly, and the other box gave the most acclimatised plants. Each arm held 16 to 35 embryos; the 4.2% is one plant out of 24. Plant density differed: 4 to 6 plants per Eco2Box vessel against 2 to 3 per box of the other type. It is one species, and which Eco2Box grade the green filter was is not confirmed.

What can the vessel not change?

A vessel cannot correct a medium that drives hyperhydricity, and it cannot change the genotype. Three limits apply to every ventilated vessel, ours included:

  • If the cause sits in the medium, for example cytokinin or ammonium, ventilation does not remove it. This point is our own reasoning.
  • More ventilation dries the medium faster. The ECO2 brochure notes that XXL+ lets a lot of air through, which could cause dehydration.
  • For some species and stages, sealed or low-exchange conditions gave better results in published work, for example wild olive and Rhododendron.

How do you test the vessel lever in your own lab?

Test one lever at a time, on your own crop, with the medium unchanged. This is our suggested set-up, not a published protocol:

  1. Pick the crop and stage where glassy shoots cost you most.
  2. Keep medium, explant source, shelf and plants per vessel the same.
  3. Run your current vessel next to two filter grades, for example XXL and XXL+.
  4. Count hyperhydric shoots per vessel at the end of the cycle, and note the medium level.
  5. Follow the plants through transfer before you decide.

Frequently asked questions

Is hyperhydricity the same as vitrification?

Yes. Vitrification is the older name for the same disorder, and hyperhydricity is the term now used. Vitrification is also the name of a method in cryopreservation, so the older word can mean two things. Eco2Box guides use hyperhydricity throughout.

Does an Eco2Box container prevent hyperhydricity?

No container prevents it on its own. An Eco2Box vessel gives you one lever, the gas exchange set by the filter grade. One study on onion found 4.2% against about 35% under one protocol, with 24 embryos in that arm, and no significant difference under the other protocol.

Which Eco2Box filter grade should I try against glassy shoots?

Start from the grade for your stage and compare it with the next grade up. The ECO2 filter guide calls XXL the standard for most propagation and suggests XXL+ for fast growers and hardening off. Watch the medium level, because more ventilation dries it faster.

Can hyperhydric shoots recover?

The sources we opened do not give a recovery rate, so we give none. What the reviews describe are measures during culture: medium changes and ventilation. In an Eco2Box vessel you can follow the shoots through the clear wall without opening the lid.

Is humidity in the vessel the cause?

Very high humidity is one cause among several, and published reviews give no universal humidity threshold. Gas build-up, cytokinin, ammonium and the gelling agent act with it. The Eco2Box filter grade changes the gas exchange; it is not a humidity setting.

Request a sample set or ask a question

To test the vessel lever on your own crop, ask for filtered Eco2Box containers in two grades. A sample set, for example of the OV80 with filter cover, is available on request: request a sample set. Tell us the crop, the stage and your medium, or ask a question first.

Related guides: What is vitrification in tissue culture?, Medium drying or condensation: more ventilation or less?.

Sources: Polivanova and Bedarev 2022, Plants 11, 3313. Barua et al. 2025, Plants 14, 3721. van den Dries et al. 2013, Journal of Experimental Botany 64, 5221. Fayos et al. 2015, Frontiers in Plant Science 6, 384, table 3. Kv values and grade guidance: ECO2 filter guide and brochure. Checked on 20 November 2026.