TL;DR Thrips in tissue culture reach a vessel in three ways: through a lid that rests loosely on the rim, with the plant material itself, or during transfer when the vessel is open. A lid that closes and locks removes the first way only. The first sign is usually fungal growth that moves from vessel to vessel, because the insects carry spores. Check your lids before you blame your technique.
Thrips in tissue culture are rarely seen before the damage is. This guide explains how they get into a closed vessel, what a lid can change, and what it cannot.
How do thrips get into culture vessels?
Thrips get into a culture vessel through the closure, with the explant (the piece of plant you start with), or at the transfer step. The closure is the route the literature describes: many vessels are closed with a cap that sits loosely so that gas can move, and that leaves room for an insect that is less than 1/20 inch long, about 1.3 mm.
| Route | What happens | What closes it | Basis |
|---|---|---|---|
| The closure | Insects walk in under a cap or lid that rests on the rim, and move on to the next vessel | A lid that closes and locks onto the vessel | Blake 1988 |
| The plant material | Females lay eggs on or into leaves and buds; the eggs travel with the explant | Clean mother plants. No vessel helps here | Thrips biology from UC IPM; the step into culture is our reasoning |
| The transfer step | An insect lands in an open vessel or on the tools and is shut in | A clean transfer area and room. No vessel helps here | Our reasoning; no study found |
Why does a loose lid let thrips in?
A loose lid lets thrips in because it is loose on purpose. In the words of Blake (1988):
Tissue culture vessels are usually closed with loose-fitting caps in order to allow gaseous exchange with the external environment.
The same abstract says that thrips may gain entry this way and travel from one vessel to another. A survey in that paper suggests that 50% of laboratories had experienced problems at some time. The abstract counts thrips together with other small arthropods, dates from 1988 and does not say how many laboratories answered. Read the figure as a sign that the problem was not rare, not as a current rate for thrips.
Loose lids have a real advantage: they are fast to handle. A lid that has to be closed adds a step per vessel.
Can thrips come in with the plant material?
Thrips can plausibly come in with the plant material, and no lid changes that. According to the UC IPM pest note on thrips, females of most plant-feeding species lay their eggs on or into leaves, buds or other places where the larvae feed. Most pest thrips feed hidden, often in buds and shoot tips, and those are parts a lab often takes as explants.
We found no study that follows thrips eggs through explant disinfection, so this route is our reasoning from the biology. If thrips show in vessels that were never opened since initiation, look at the mother plants first.
What is the first sign of thrips in tissue culture?
The first sign of thrips in tissue culture is usually fungal contamination, not the insect. Blake (1988) writes that the insects carry fungal spores and bacteria in and on their bodies, and that fungal contamination of cultures is usually the first sign of an infestation.
- Fungal growth that appears in several vessels on one shelf, one after the other.
- Growth that starts away from the explant, where an insect walked over the medium. This pattern is our reasoning from Blake’s description.
- Silvery or scarred patches on leaves, the feeding damage UC IPM describes on plants in general.
Speed matters. When the weather is warm, the life cycle from egg to adult can be completed in as little as 2 weeks, according to UC IPM, which describes thrips on garden and outdoor ornamental plants. We found no figure for a growth room.
How do you check your own vessels and growth room?
Check the lid first, then the room, then the mother plants. These five checks are our own practical suggestions and need no new vessels. They are not a published protocol.
- Take a closed vessel from the shelf and lift the lid straight up, without twisting or unclipping. If it comes off, the lid rests on the rim.
- Hold a closed vessel against the light and look along the line where lid meets vessel.
- Hang blue or bright yellow sticky traps near the transfer area and the shelves. UC IPM names both colours for detecting flying thrips.
- Note where each contaminated vessel stood. Neighbours on one shelf point to insects that walk.
- Inspect the mother plants and the room they come from before you change anything in the lab.
What does a lid that locks change, and what does it not?
A lid that locks removes the gap between lid and vessel, and nothing else. The Eco2Box cover closes hermetically onto the vessel and locks. With the cover closed, gas exchange runs through the filter in the cover, so the lid does not need to sit loose for the plants to get air. ECO2 nv describes the closure as 100% hermetically sealed, which is a statement about the closure only.
| Question | Lid that rests on the rim | Eco2Box filter cover |
|---|---|---|
| How does gas get in and out? | Through the gap between lid and vessel | Through the filter in the cover |
| Is there a gap at the rim? | Yes, by design | No, the cover closes and locks |
| Handling | Fast: lift and replace | One extra step: the cover has to be closed |
| Does it help with eggs in the plant material? | No | No |
No published study that we know of compares insect entry between closure types, for any brand. What is written here is the mechanism, not a measured rate. Not every Eco2Box article has this closure: the polystyrene RA trays with RDA covers have no filter and are not hermetic.
Which mistakes keep thrips in the lab?
One mistake that keeps thrips in the lab is to treat them only as a contamination problem at the bench. Blake reports that laboratories got outbreaks under control with thorough disinfection and strict hygiene in the laboratory. The other mistakes below are our own reasoning.
- Leaving contaminated vessels on the shelf, where insects can walk on to the next one.
- Judging a lid by its filter. The filter is there for gas exchange; the closure is what shuts the gap.
- Choosing a higher filter grade to keep insects out. The grade sets the gas exchange, as the guide on choosing a filter grade explains.
- Changing vessels while the mother plants still carry thrips.
Frequently asked questions
Can thrips get through a filter lid?
The question to ask is whether the lid closes. In an Eco2Box set the cover closes and locks onto the vessel and gas passes through the filter in the cover. We know of no published test of insect entry for any closure, so ECO2 nv describes the mechanism and gives no rate.
Does a higher filter grade let thrips in?
The filter grade changes the gas exchange, not the way the lid closes. Eco2Box filter covers come in four grades, L, XL, XXL and XXL+, and each one sits in a cover that closes hermetically onto the vessel.
Why do I see fungus before I see thrips?
Thrips carry fungal spores and bacteria in and on their bodies, so the fungus they leave behind shows first. Blake (1988) calls fungal contamination the usual first sign. An Eco2Box vessel is clear, so you can inspect it without opening the lid.
Do thrips only affect some crops?
We found no published list of crops at risk in vitro. The way in is the same for every crop: a gap at the lid, the plant material or the transfer. An Eco2Box cover closes the first of these.
Can I autoclave Eco2Box vessels after an outbreak?
Untreated polypropylene Eco2Box vessels and covers are autoclaved at 121 °C before first use; we recommend at most 5 uses, and the material becomes more brittle each cycle. Gamma irradiated articles are supplied sterile; autoclaving them is not recommended (at most 2 to 3 cycles, and the plastic turns brittle and yellowish).
Request a sample set or ask a question
If the lid is your open route, test a locked lid next to your current vessels, on the cultures where losses hurt most. A sample set of filtered Eco2Box containers such as the O118/80 with filter cover is available on request: request a sample set. Tell us the crop and your current closure, or ask a question first. The full list is on the product range page.
Related guides: Plant tissue culture contamination: where it comes from, Glass or polypropylene for plant tissue culture.
Sources: Blake 1988, Acta Horticulturae 225, pages 163 to 166, doi 10.17660/ActaHortic.1988.225.17 (abstract). University of California IPM, Pest Notes: Thrips. Eco2Box facts: ECO2 product sheets. Checked on 20 November 2026.